Related Searches : Veneer ComposerCore ComposerVENEER COMPOSER FOR BACKCore VeneerSEMI-AUTOMATIC BLOCK BOARD COMPOSERcomposer

Automatic Veneer Core Composer

  • Supplier - CHANG I IN CO., LTD.
  • China(Taiwan)China(Taiwan)
  • 5 - 10 People
  • Manufacturers
  • North America,South America,Eastern Europe,Southeast Asia,Africa,Oceania,Mid East,Eastern Asia,Western Europe
  • Mr.Shun-Hao
  • 886-7-7031896
Post Date : September 09
Product Details
Company Profile
Inquiry Records(1)

Item specifics

Kaohsiung
Taiwan
L/C,T/T

Specifications

Automatic core builder

AUTOMATIC CORE BUILDER INTRODUCTION 

MAIN PART

1. After tenderized using PLC controller to cut the edge, joint the core and piece cutting.

2. After the core has been tenderized. The strong blower device can remove the dust one the core veneer

3. The PLC controller enables cutting more precise, it can available reduce the odd core. It helps control, monitor and maintenance more convenient.

4. The back-feeding wheel device is synchronizing with feeding speed, to avoid overlap or gap of the jointing core.

5. It is equipped with hot melt glue yarn for help jointing. Cooling water tank of glue yarn is circle well by the cooler. It gets the best joint.

TENDERIZER

Before the veneer is composed, it should be rolled by tenderizer first ,so that veneer will be softer and more extended for cutting and jointing, the veneer using is economized. It also can prevent to overlap and be sure to get the high quality plywood.

1. The pressure of tenderizer is by air cylinder it can be adjusted by regulator , it is steadily.

2. The tenderizer has highly hard wheel and low roller. The core veneer had tenderized is softly extended without curve. That is easy to cutting, jointing  and next process.

3. Tenderizer roller are made of special steel and special quenching. So that the strength and quality are reliable.

STACKER

Composed veneer after cutting, clearing dust, received by stacker.

1. In front of stacker, there is a strong blower to clear dust and clip for after stacking the core can be send to glue spread process directly.

2. The mid pressing bar and the side stacking wheel rack can be moved free for easy adjustment in the dimension easy to collection.

SPECIFICATIONS

MODEL

CI-CB

Length of Knife

1350 mm

Working Veneer Core Width

968 mm to 1270 mm (3ft. to 4ft)

Veneer Core Thickness

1.2 mm to 2.2 mm /2.0 mm to 5.0 mm

Feeding Speed

31m/min(Constant)

MOTOR

Tenderizer

2.2kw

Feeding

3.7kw

Heater

7.5kw

Glue Applicator

0.2kw

Cool Fan

0.75kw X 3

Full-size Clipping

1.5kw

Stacker Table Lifting

2.2kw

Stacker Feeding

0.4kw

 Optional Accessories: Air compressor with 3.7kw motor

  (required 7kg/cm air pressure. 1200 liters/min. free air

Company Related ProductsView the Seller's Products
Veneer Peeling Lathe

Veneer Peeling Lathe

Veneer Peeling Lathe

Super Small Diameter Log Veneer Lathe

 

TANOUCHI SUPER SMALL DIAMETER LOG VENEER LATHE

INTRODUCTION

It is increasingly the most important subject for todays plywood and veneer factories how to make efficient use of the small diameter plantation log & unused log into quality veneers with high recovery.

Exactly ,TANOUCHI MODEL BV-5 (BEAVER) VENEER LATHE are developed for peeling various small diameter log into accurate, constant thickness veneers with higher recovery.

The (BEAVER LATHE) are ideal for peeling the following small diameter logs

1. Small diameter plantation ALBZZIA,ACACIA,RUBBER WOOD etc.

2. Small diameter various tropical wood, needle-leaf tree as cedar, pine.

3. Small diameter swamp logs.

4. Remain peeled cores form big size veneer lathe.

 

POINTS OF BEAVER LATHE

1. TWIN PERIPHERAL DRIVER

Upper & Lower twins peripheral drive roller rotate the log while holding the log along its all length at upper & lower position by hydraulic power.

Form beginning to end, the log is held by the twin drive rollers and peeled down to the final minimum core diameter constantly without vibration

2. CASSETTE ROLLER PRESSURE BAR SYSTEM

Roller type pressure bar with bearing inside, short size cassette composition.

Comparing to fix nose bar , the cassette roller bar minimize cutting resistance for stable peeling operation.

3. SERVO CONTORL FEEDING SYSTEM

When you change veneer thickness ,no need to charge the thickness gear.

Carry out the accurate knife feeding electrically, and thickness setting can be done by 0.01mm scale. 

4. SWING TYPE CENERING CHARGER SYSTEM

Mechanical hydraulic power system auto centering charger.

During the peeling operation , the centering charger continuously carryout the centering and chargering.

BEAVER STANDRD SPECIFICATIONS

ITEM

MODEL   BV-5

Log Diameter

150~400mm

Log Length

950~1350mm

Length Knife

1450mm

Log Drive System

Twin Peripheral Drive Rollers

Spindle

Double Spindles

Pressure Bar

Cassette Type Roller Bar

Knife Setting

Hydraulic Clamp

Chuck Diameter

Out Chuck 123mm   Inner Chuck55mm

Veneer Thickness

1.0mm~3.5mm   Digital Input

Peeling Speed

70 meter/min

Auto Log Input

High Speed Centering Charger

Main Motor

DC37kw

Detail more >>
Veneer Core Builder

Veneer Core Builder

Veneer Core Builder

THE COUNTRY OF DELIVERY: INDONISIA
THE QUANTITY OF DELIVERY: 10 SET

MEINAN CORE BUILDER SPECIFICATIONS

 

ITEM

MODEL   NFC-4TR

Working Veneer Length

960~1270 mm

Format Sheet Cutting

1800~2600 mm

Veneer Thread Melting

1.3~2.0 m/m

Glue Thread Melting

7~9 pcs

Min Veneer Log

50 m/m

Feeding Speed

30M/min

Glue Speed cycle

0.7Sec/Cycle

Power Supply

10kw

Air Supply

0.1M / min

 

 

Detail more >>
You may also be interested in:pine core veneercore veneer plywoodEucalyptus core veneerVeneer Core Builderacacia core veneerCore veneer glue spreader
Talk with SupplierX
Hsu Shun-Hao:
Can I help you?
Contact Supplier

Selected(1/4)Contact or Compare