Boysen Zinc Chromate Primer Yellow #320 Building Coating  

DESCRIPTIONHudson Polyurethane Floor Varnish Topcoat is an aromatic, two-component, urethane finish for wooden surfaces that cure to a tough, non-slip, mar resistant film. PRINCIPAL USESExcellent for wood parquet, counter-tops, and other wooden floorings (indoor use). PRACTICAL COVERAGE20 - 25 sq.m./4 liters/coat SURFACE DRYThirty (30) minutes DRY THROUGHOne (1) hour DRY FILM THICKNESS1.5 mils/coat OVERCOATING INTERVALRecoat after 6 hours APPLICATIONBy camel brush or spray THINNINGHudson Polyurethane Reducer PACKAGINGHudson Polyurethane Floor Varnish Topcoat - 4 liter can Hudson Polyurethane Floor Varnish Catalyst - 1 liter can SURFACE PREPARATIONSurface to be painted should be clean and dry, free from dust, dirt and other foreign matter. Hammer all nails deep enough to apply wood filler. Sand rough wood until smooth, then dust off before painting. If repainting, first remove all blistering, peeling and scaling paint by wire brushing or Boysen Paint and Varnish Remover #141. Solvent wipe after treatment. MIXINGHudson Polyurethane Floor Varnish Topcoat is mixed on a 7:1 ratio by volume to its catalyst. Enough material should be made for four hours work (maximum). Excess mixture will gel. PAINTING SCHEDULENew Wood - Apply 1 to 2 coats of Hudson Polyurethane Floor Varnish Sealer by brush or spray. Follow with 3 coats of Hudson Polyurethane Floor Varnish Topcoat applied by spray. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traffic abrasion. REPAINTING SCHEDULEOld varnish film in bad condition should be stripped with Boysen Paint and Varnish Remover #141, sand then surface cleaned. Proceed as in New Wood." Old varnish film in good condition should be lightly sanded. Surface is cleaned before painting with topcoat. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traffic abrasion

DESCRIPTIONBoysen Bridge and Tank Aluminum Paint # 85 is a highly reflective grade of aluminum paint ideal for storage tanks and structural steel, since it tends to keep these cooler. PRINCIPAL USESFor storage tanks, structural steel and other industrial metal surfaces. PRACTICAL COVERAGE20-25 square meter / 4 liters / coat SURFACE DRY2-4 hours DRY THROUGHOvernight DRY FILM THICKNESS1.5 mils OVERCOATING INTERVALAllow 24 hours before recoating THINNINGNot necessary APPLICATIONBy brush PACKAGING4-liter cans SURFACE PREPARATIONMetalsWipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). If repainting, wire brush or scrape rusted metals and apply Boysen Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner, letting it dry before applying paint. Primer should be applied immediately after treatment to prevent flash rusting. PAINTING SCHEDULENew metal (ferrous) 1st coatBoysen Red Oxide Primer #310 2nd and 3rd coatBoysen Bridge and Tank Aluminum Paint # 85 New metal (non-ferrous) 1st coatBoysen Zinc Chromate Primer Yellow # 320 2nd and 3rd coatBoysen Bridge and Tank Aluminum Paint # 85